STM32F030F4P6

The mikromedia 7 displays are smart programmable touch displays, packed with features and with M4 or M7 MCU flavor. Mikromedia 7 can be used as a powerful programmable dashboard control panel for both hobby projects, but also for the entire systems. Mikroe offers mikromedia 7 boards with Resistive 7” type of displays which represents a powerful tool for building GUI-centric HID applications.<p>Features: 7\\" full-colored resistive touch screen, ST WiFi module SPWF01SA, programmer debugger, 8 Mbit of Serial Flash, microSD card slot, VS1053 MPEG audio decoder, Piezo Buzzer, USB OTG connector, Temp. sensor, RTC battery, PIN photosensor, Accelerometer, Battery Charger, headers for additional connection.<p>There are two versions of this board: mikromedia 7 for STM32F7 and mikromedia 7 for STM32F4.

mikromedia for STM32® are compact development systems with lots of on-board peripherals which allow development of devices with multimedia contents. The central part of the system is a 32-bit STM32F207VGT6 or STM32F407VGT6 microcontroller.<p>mikromedia for STM32® features integrated modules such as stereo MP3 codec, 2.8” TFT 320x240 touch screen display, accelerometer, USB connector, MMC/SD card slot, 8 Mbit flash memory, 2x26 connection pads and other. It comes preprogrammed with USB bootloader, but can also be programmed with external programmers, such as mikroProg™ for STM32® or ST-LINK. Mikromedia is compact and slim, and perfectly fits in the palm of the hand, which makes it convenient platform for mobile devices.<p>There are two versions of this board: mikromedia for STM32 M4 and mikromedia for STM32 M3.

MINI for STM32 are a small ARM® Cortex™-M0/M4 development boards containing STM32F051R8/STM32F415RG microcontroller.<p>This form factor perfectly fits into standard DIP40 sockets. Boards are equipped with 16MHz SMD crystal oscillator, and 32.768KHz crystal which can be used for internal RTCC module. It has reset button and three signal LEDs. Board comes preprogrammed with fast USB HID bootloader, so no external programmers are needed for development. It operates on 3.3V power supply. On-board voltage regulator allows the board to be powered directly from USB cable.

Full-featured development board for STM32 ARM® Cortex™-M0, -M3, -M4 and -M7 microntrollers, it contains many on-board modules necessary for development variety of applications. Features: including multimedia, Ethernet, USB, CAN and on-board mikroProg™ programmer.

Clicker 2 for STM32 is a battery-powered click board two-seater and compact development board for STM32F407VGT6 which Feature: battery connector for powering board, two mikroBUS sockets and GPIO pins, USB connector, pushbuttons.

Mikroe provides dozens of MCU Cards which supports hundreds of Arm® Cortex®-M processors from M0, M3, M4 and M7. The 8th generation of MCU card is a standardized add-on board, which allows very simple installation and replacement of the microcontroller unit (MCU) on a development board equipped with the MCU Card socket. MCU Cards are equipped with two 168-pin mezzanine connectors, allowing them to support even MCUs with extremely high pin count. Their clever design allows very simple usage, following the well-established plug & play concept of the Click board™ line of product. For the complete list of boards and supported MCU’s, please visit official Mikroe page.

The mikromedia+ for STM32 ARM® is a compact development system with lots of on-board peripherals which allow development of devices with multimedia contents. The central part of the system is a 32-bit ARM® Cortex™-M7 or M4 microcontroller.<p>The mikromedia+ for STM32 ARM® features integrated modules such as stereo MP3 codec, 4.3’’TFT 480x272touch screen display, accelerometer, microSD card slot, buzzer, IR receiver, RGB LED diode, PIN photodiode, temperature sensor, 2.4GHz RF transceiver, Ethernet transceiver, 8 Mbit flash memory, RTC battery, Li-Polimer battery charger etc.<p>There are two versions of this board: mikromedia Plus for STM32F7 and mikromedia Plus for STM32.